Product

Test and Measurement

Data Acquisition System Omniace RA3100

・All data recorded in Omniace

・High-speed, long-term recording of phenomena on large-capacity storage media

Omniace RA3100 is a data acquisition system for research, development, and field maintenance, which enables accurate and long-term measurement of high-speed switching waveforms, even in severely noisy environments, in electric automobiles, electronic appliances, railroad cars, and solar power generation systems utilizing inverter control technology that has become widespread in recent years.

Brochure

Manual English Korean Chinese

Manual Simplified English Korean Chinese

Communication command Manual

Viewer Manual English Korean Chinese

File Converter Manual English Korean Chinese Simplified Chinese Traditional

Software Download

Features

■ Multi-channel Input

Max 36ch (analog input), Max 144ch (logic input)
"The 4ch Voltage Module" allows 4-channel input with a single unit.
9 modules can be installed in the main unit, allowing 36-channel recording.
"The 16-channel Logic Module" allows 16-channel logic signal input with a single unit.
9 modules can be installed in the main unit, allowing 144-channel logic signal recording.

■ High-speed Sampling and High-definition Measurement at 20MS/s with 18ch for 5 seconds

"The 2ch High-Speed Voltage Module" is an input module for high-speed sampling at the highest level of the series. Includes the ability for a sampling rate of 20MS/s, input voltage up to ±500V, and 14bit resolution. 9 modules can be installed in the main unit, allowing for 18-channel high-speed memory recording.

■ Long-term Recording

Various recording speeds, multiple channels, and a high-capacity storage medium to support a large amount of data are included as standard.
Recording desired signal accurately without missing detailed changes.

Memory capacity of 4GB (when 18 channels are used, 20MS/s, 5 seconds)
SSD capacity of 256GB (when 36 channels are used, 1MS/s, approximately 59 minutes)

■ High-speed and High-definition printing

High-resolution waveform printing at high speeds (100mm/s) is possible.
Even if the chart paper runs out, recorded data is backed up to the SSD and can be printed out later.

■ Various Recording Method

The data recording destinations include "memory," "SSD," and "printer".Data recording can be performed at three destinations at the same time. In addition, "pen recorder recording" is also possible, which records data only on recording paper for simplified measurements.
You can freely select depending on the purpose of your measurement.

Memory Recording

Memory mode records data in the internal memory (4GB) at high speed (Max: 20MS/s).
In addition, measurement can be performed under a variety of conditions using a variety of trigger functions.

After the input data is recorded in the memory, it is automatically saved to SSD.
Sampling speed: 20MS/s to 10S/min (depending on the input module)
Memory capacity: 4GB (2G point/ch)
Memory divisions: 1 to 200 divisions
Recording length: 2,000 to 2G points/ch (1-2-5 step)
Total Memory Capacity
Memory Block Segment

Recordable Time on Memory

Sample speed	2ch	8ch	18ch	36ch
20MS/s	50 sec	10 sec	5 sec	-
10MS/s	1 min 40 sec	20 sec	10 sec	5 sec
5MS/s	3 min 20 sec	40 sec	20 sec	10 sec
2MS/s	8 min 20 sec	1 min 40 sec	50 sec	25 sec
1MS/s	16 min 40 sec	3 min 20 sec	1 min 40 sec	50 sec
500kS/s	33 min 20 sec	6 min 40 sec	3 min 20 sec	1 min 40 sec
〜	〜	〜	〜	〜
10kS/s	27 hrs 46 min 40 sec	5 hrs 33 min 20 sec	2 hrs 46 min 40 sec	1 hrs 23 min 20 sec
5kS/s	55 hrs 33 min 20 sec	11 hrs 06 min 40 sec	5 hrs 33 min 20 sec	2 hrs 46 min 40 sec
2kS/s	138 hrs 53 min 20 sec	27 hrs 46 min 40 sec	13 hrs 53 min 20 sec	6 hrs 56 min 40 sec
1kS/s	277 hrs 46 min 40 sec	55 hrs 33 min 20 sec	27 hrs 46 min 40 sec	13 hrs 53 min 20 sec

SSD Recording

Long-term of data can be recorded to the internal SSD.
High-speed recording of up to 1MS/s is possible when using 36ch.
Since it is stored as digital data, data can be analyzed after recording and data can be managed for a long period of time.

Input data is saved directly to SSD.
Sampling speed: 1MS/s to 10S/min (depending on the input module)
SSD capacity: 256GB
Maximum recording time: 100 days
Data format: Normal data, Peak data

Recordable Time on SSD ^*1

Sample speed	2ch	8ch	18ch	36ch
1MS/s^*2	11 hrs 46 min 40 sec	3 hrs 55 min 33 sec	1 hrs 51 min 34 sec	57 min 17 sec
500kS/s	23 hrs 33 min 21 sec	7 hrs 51 min 07 sec	3 hrs 43 min 09 sec	1 hrs 54 min 35 sec
200kS/s	2 day 11 hrs 20 min 02 sec	19 hrs 37 min 48 sec	9 hrs 17 min 54 sec	4 hrs 46 min 29 sec
100kS/s	4 day 21 hrs 46 min 49 sec	1 day 15 hrs 15 min 36 sec	18 hrs 35 min 48 sec	9 hrs 32 min 59 sec
50kS/s	9 day 19 hrs 33 min 39 sec	3 day 06 hrs 31 min 13 sec	1 day 13 hrs 11 min 37 sec	19 hrs 05 min 58 sec
20kS/s	24 day 12 hrs 54 min 09 sec	8 day 04 hrs 18 min 03 sec	3 day 20 hrs 59 min 04 sec	1 day 23 hrs 44 min 55 sec
10kS/s	49 day 01 hrs 48 min 19 sec	16 day 08 hrs 36 min 06 sec	7 day 17 hrs 58 min 09 sec	3 day 23 hrs 29 min 51 sec
5kS/s	98 day 03 hrs 36 min 38 sec	32 day 17 hrs 12 min 12 sec	15 day 11 hrs 56 min 18 sec	7 day 22 hrs 59 min 43 sec
2kS/s	100 day	81 day 19 hrs 00 min 31 sec	38 day 17 hrs 50 min 46 sec	19 day 21 hrs 29 min 19 sec
1kS/s	100 day	100 day	77 day 11 hrs 41 min 33 sec	39 day 18 hrs 58 min 38 sec
500S/s	100 day	100 day	100 day	79 day 13 hrs 57 min 16 sec
200S/s	100 day	100 day	100 day	100 day

*1 If you select peak data as the data type, the time will be 1/2 of the above time.
*2 A sample rate of 1 MS/s is not available when peak data is selected as the data type.

Window Recording

Endless recording is possible by specifying the ring buffer area (maximum 2G points/ch) as the window recording time. If you do not know when an abnormality will occur, you may miss the abnormal data if you set the recording time and measure. By ringing the recording area, you can always save the latest data.

Selectable for SSD Recording

Omniace is a digital recorder that performs analog to digital conversion on all inputs and records those signals. Due to the relationship between the speed of analog to digital conversion and the frequency component of the input signal, the data may or may not be measured correctly.

Normal Data

Normal data is recorded at each designated sampling speed. (□ points)
If the signal changes too fast relative to the sampling speed, the data singular point (peak value) may not be recorded. Memory recording can measure this type of data.

Peak Data

Peak data is sampling (■, ■, and □ points) between the designated recording speed at the fastest AD-conversion rate, and records two data points, the maximum value (■ points) and the minimum value (■ points). The amount of data can be compressed without losing the data singular point (peak value).
Printer recording records data of this method on the chart paper.

Printer Recording (Pen-Recording)

Input data is printed directly on the chart paper at high speed (MAX 100 mm/s). Data printed on chart paper is also stored digitally on the SSD, so even if the chart paper runs out, the data can be printed out later.

Pen-Recording

Pen records are only recorded on recording paper; measurement data is not stored. Input module and paper feed rate settings can be configured during recording.

Recording Specifications
　Number of recorded signals: 48 channels
　Chart speed: 100mm/s(1kS/s）～1mm/min(10S/min) 　
　Recording resolution: 20 to 80dots/mm (time axis) 8dots/mm (amplitude axis)

■ Input Modules

Up to 9 modules can be installed in the main unit.
Various modules for high-speed voltage, high-accuracy voltate, logic inut, temperature measurement, and remote control are available.

Module Name	Model	Channels	Sampling Rate	Input	Specifications
2ch Voltage Module	RA30-101	2ch	1MS/s	Voltage ±500V	Measure high-speed voltage measurement with anti-aliasing filters
4ch Voltage Module	RA30-102	4ch	1MS/s	Voltage ±200V	Multi-channel voltage measurement
4ch Voltage Module	RA30-113	4ch	1MS/s	Voltage ±500V	Multi-channel voltage measurement
2ch High-speed Voltage Module	RA30-103	2ch	20MS/s	Voltage ±500V	High-speed voltage measurement
2ch High Voltage Module	RA30-107	2ch	1MS/s	Voltage ±1,000V	Module to measure high voltages of ±1,000 V
16ch Logic Module	RA30-105	16ch	1MS/s	Contact, Voltage	Contact, Voltage signal measurement
2ch Temperature Module	RA30-106	2ch	1.5ms	Thermocouple : K, E, J, T, N, R, S, B, C RTD: Pt100, Pt1000	Measurement of temperature with a thermocouple and RTD
2ch AC Strain Module	RA30-104	2ch	100kS/s	Strain gauge, Strain gauge transducer	Module to measure stress, load, displacement, pressure, torque, and acceleration
2ch Acceleration Module	RA30-109	2ch	1MS/s	Piezoelectric acceleration transducer (charge output, built-in amplifier)	Module to measure acceleration, speed and displacement
2ch Frequency Module	RA30-108	2ch	1MS/s	Voltage ±500V	Input module capable of measuring period, rotation speed, number of pulses, etc., of input signals　　　 Module to measure stress, load, displacement, pressure, torque, and acceleration

■ Excellent Visibility and Operability

The LCD display with touch panel allows zoom in and out, and scrolling through the waveform simply,
allowing a dynamic waveform drawing and operability like a smartphone. Pinch-in Pinch-out Swipe

■ Back scrolling

Press the [PAUSE] button during recording to playback recorded data while recording.
Recording start Recording during monitoring Playback monitoring Continuous recording

■ Various Monitor Displays

Input signal and recorded data can be displayed as Y-T waveform display, X-Y waveform display, and FFT.

Y-T Waveform Display

Display the measurement channels split into three sheets.
Monitors up to 48 channels of signals on a sheet with 20 divisions in vertical and horizontal.
Graphs can be divided into 1 to 18 sheets and displayed.

Set the signal display width and display position.

Signals can be drawn at any position on the graph at any width.You can easily draw a 100V signal in the width of 1div.

Display Width
Display the signals of each channel at any width.
Set the width of the channel to be displayed as % out of the 100% width of the display graph.

Display Position
Set the position of the channel to be displayed as % out of the 100% width of the display graph.

Scale Setting
Set the upper limit/lower limit value of display for the display width of each channel as an input value or a physical conversion value.

X-Y Waveform Display

An X-Y screen format can be drawn by specifying 4 channels for the X-axis and 4 channels for the Y-axis. The graph can be displayed a large single screen format, or devided four screen format for the each X and Y axis channels. The pen can also be moved up or down, and the grid can be turned on or off.

FFT Analysis

FFT analysis is performed for any two signals. The top 10 highest values can be read from the analysis results, and the value of any analysis result can be read using the cursor. (FFT analysis can be performed on normal data recorded in SSD.)

Recording Mode Selection
Nine measurement patterns are prepared as recording modes.
"Recording Mode" can be selected from Measurement starts by manual operation, Measurement starts from a trigger signal or Repeating measurement, etc. When "Recording Mode" is selected, the necessary set-up menu is displayed and can be easily set.

PC Compatibility

Web server, FTP server	Software for displaying measurement data^*3
The RA3100 can be remotely operated from a web browser (operating PC). The web browser displays the same screen as the RA3100 main unit with pseudo operation panel keys (START key, etc.) to make settings and start/stop recording. Additionally, data stored on the RA3100 can be transferred to a PC.	"RA3100 Viewer" is software to display recorded data exported to external media from an RA3100 on a PC.
	PC software for converting measurement data^3 The "File Converter" software can convert recorded data exported to external media from an RA3100 to CSV or ASAM MDF (Ver. 4.1) files on a PC. 3 The software can be downloaded from our website: https://www.aandd.co.jp/support/soft_download/industrial.html

Input Module and Peripheral Option Selection Guide

Page Top